allinone 02spercelnazogz: Konica minolta bizhub c360 service manual free download

Looking for:

- Konica Minolta Bizhub C C C SERVICE MANUAL -

Konica minolta bizhub c360 service manual free download.Download Center

Quick Links. See also: Service ManualOperating Manual. Table of Contents. Previous Page. Next Page. Konica Minolta bizhub C User Manual pages. Konica Minolta bizhub c User Manual pages. S Composition of the service manual C-1 Notation of the konica minolta bizhub c360 service manual free download manual This reliability is achieved through high-quality design and a solid service network.

Product design is a highly complicated and delicate process where numerous mechanical, physical, and electrical aspects have to be taken into consideration, with the aim of arriving at proper tolerances and safety factors.

In that case, it is obligation of customer engineer hereafter called the CE to attach appropriate power plug or power нажмите для деталей set in order to connect the product to the supply. However, in daily use, any electrical equipment may be subject to parts wear and eventual failure. When securing measure is provided, secure the cord with the fixture properly. If used, the risk of fire konica minolta bizhub c360 service manual free download. Current that can flow in the extension cord is limited, so using a too long extension cord may result in fire.

If a bad smell of ozone is present in the following cases, ventilate the room. If you make adjustments or perform an operation check with the external cover detached, you may touch live or high-voltage parts or you may be caught in moving gears or the timing belt, leading to a risk of injury.

Current can leak, leading to a risk of trouble or fire. Pay special attention to forgotten connectors, pinched cables, forgotten screws, etc. A risk of product trouble, electric shock, and fire exists. If this happens, immediately wipe it off.

A risk of fire exists. Replace only with the same or equivalent type recommended by the manufacturer. When accessing these areas for maintenance, repair, or adjustment, konica minolta bizhub c360 service manual free download care should be taken to avoid burns and electric shock. Be careful not to touch here when the power is turned ON to avoid getting an electric shock.

High konica minolta bizhub c360 service manual free download This area generates high voltage. If an accident has occurred, the distributor who has been notified first must immediately take konica minolta bizhub c360 service manual free download measures to provide relief to affected persons and to prevent further damage.

Page Composition Of The Service Manual Composition of the service manual This service konica minolta bizhub c360 service manual free download consists of Theory of Operation section and Field Service section to explain the main machine and its corresponding options.

Theory of Operation section gives, as information for the CE to get a full understanding of the product, a rough outline of the object and role of each function, the relationship between the electrical system and the mechanical system, and the timing of operation of each part. Page Revision History Revision history After publication of this service manual, the parts and mechanism may be subject to change for improvement of their performance.

Therefore, the descriptions given in узнать больше service manual may not coincide with the actual machine. When any change has been made /14606.txt the descriptions in the service manual, a revised version will be issued with a revision mark added as required.

Page 28 Theory of Operation Ver. Page 29 Theory of Operation Ver. Page 30 Theory of Operation Ver. Page 31 Theory of Operation Ver. Page 32 Theory of Operation Ver. Page 33 Theory of Operation Ver. Page 38 Theory of Operation Ver. Page Paper 2. Page Materials Theory of Operation Ver. Page Print Volume 2. Page 43 2. Page Scan Functions 2. Page Image Creation Process 6. Page 50 Theory of Operation Ver. Page Image Forming Control 6.

Page Right Side 7. Page 54 Theory of Operation Ver. Page 55 7. Page 56 Theory of Operation Ver. Page 57 7. Page Drive 8. Page Operation Theory of Operation Ver. The exposure unit moves from the scanner standby position to the home position. Exposure unit moves from the home position to the shading position under the shading correction узнать больше and stops in scanning direction. Original scanning mode Original scanning mode has two types: Original cover mode and DF mode.

Page 62 Theory of Operation Ver. The exposure unit will move to the reading position and stops. The document will be read as the paper is konica minolta bizhub c360 service manual free download. Page Original Scanning Area 8. Automatic document feeder or Original cover Angle sensor PS Page 65 8. Page Write Section Ph Section 9. A semiconductor laser is provided for each of four different colors. Page Laser Exposure Больше информации 9.

Operation 1. The K laser light enters the cylindrical lens via the return mirror light source. The Y, M, and C laser light enter the cylindrical lens via the synthetic mirror and return mirror light source. Page Laser Emission Stop 9. Page 74 Theory of Operation Ver. Page 75 9. Page 76 Theory of Operation Ver. Page Color Skew Correction Control 9. This may cause color skew problems.

To prevent the problems, individual G3 lenses that correspond to Y, M, and C respectively have a color skew auto adjustment mechanism. Page 78 Theory of Operation Ver. This could result in image problems, including white bands or white lines on the print image.

Page Image Processing 9. See P. Page Drive Page 85 The potential left on the photo conductor after the toner image is transferred is neutral- ized by turning ON the erase lamp and any potential left on the surface of the photo con- ductor is neutralized.

Посмотреть еще Photo Conductor Cleaning Part of the toner image that is not transferred is left on the surface of the photo conduc- tor.

Page 90 Theory of Operation Ver. Konica minolta bizhub c360 service manual free download Charge Corona Control Charge discharged from the comb electrode causes the surface of the photo conductor to become uniformly charged via the charge corona control plate.

Page Ozone Filter Page 95 Page 97 If the drum rotation time counter value reaches the thresh- old, the machine determines that the drum unit has reached a new state. Page 98 Theory of Operation Ver. Page 99 Page Ozone Filter Life Detection Page Theory of Operation Ver. Page Developing Section Page Drive Theory of Operation Ver.

Konica minolta bizhub c360 service manual free download

Quick Reference. Store this guide next to the machine for future reference. User s Guide. Security Operations. Legal Notes. Regarding Trademarks. We cannot be held liable for any problems arising from More information. Chapter More information.

Check your network More information. Introduction About More information. This manual provides instructions More information. This guide describes how to troubleshoot More information. Page 1 - page1. Quick Reference Guide. Select the [Copy] function More information.

Contents of this publication may not be reproduced More information. Replenish the cash If using less than 75 bills, disable More information. Changes are periodically More information. Contents of this publication may More information. Xe, Xe. Caution q s Indicates procedures More information. Monochrome Image Quality Problems I.

Attention s Indicates procedures More information. Quick Scan Features Setup Guide. Scan to E-mail Setup. Understanding the home screen Quick Reference Learning about the printer Using the printer control panel 1 2 3 4 5 6 Understanding the home screen When the printer is turned on, the display shows a basic screen, referred to as the More information.

This manual explains the instructions More information. Scan to FTP Guide. To find basic information about network scanning features More information.

Model supported by the KX printer driver. We cannot be held liable for any problems More information. Safety More information. If you work through the procedures in More information. Remove five screws [1], and remove the MFP board assy [2]. Remove two ground plates [1]. Remove six bolts [1], and remove the interface cover [2].

Remove the DIMM. Disconnect 11 connectors [1]. Remove seven screws [1], unhook the tab [2], and remove the high volt- age unit [3]. NOTE Install the high voltage unit so that the machine terminals come into contact with the counterparts on the high voltage unit and the high voltage unit properly fit into the tab.

Remove two screws [1], and remove the metal plate [2]. Unhook two tabs [2], and remove the paper feed tray 1 paper FD sensor board assy [3]. Remove the lever [1], and remove the paper feed tray 1 paper FD sen- sor board [2].

NOTE When removing the lever, be careful not to deform the lever. Unhook two tabs [2], and remove the paper feed tray 2 paper FD sensor board assy [3]. Remove the lever [1], and remove the paper feed tray 2 paper FD sen- sor board [2]. Raising the front knob [1], remove two screws [2] and the front right cover [3]. Remove two screws [1] and place the lower front cover with the inside up.

Remove the screw [1] each, discon- nect the connector [2] each, and remove the paper feed tray 1 LED board [3] and the paper feed tray 2 LED board [4]. Remove the upper right cover. Disconnect the connector [1], and remove the harnesses from two wire saddles [2] and two edge covers [3]. Remove the screw [1], and remove the angle sensor assy [2]. Remove six screws [1], and remove the ADF base plate [2]. Disconnect the connector [1], and remove three screws [2]. Remove the spring [1] and the belt [2], and remove the scanner motor assy [3].

Remove two screws [1], and remove the bracket [2]. Remove two screws [1], and remove the damper [2]. Temporarily secure the scanner motor assy [1] with three screws [2]. With the scanner drive gear set screw [1] located on the right-hand side as shown on the left, slide the scanner motor assy [2] to the left and check that it is returned to the origi- nal position by the tension of the spring [3].

Perform this step three times. Turn the pulley and make sure that the belt does not ride up on the pul- ley teeth. Tighten the three screws [4] to fix the scanner motor assy [2] into position. Remove the regist unit. Remove two screws [1] and remove the 2nd transfer unit [2] as shown in the illustration. Disconnect the connector [1], and remove the harnesses from six wire saddles [2]. Remove 15 screws [1], and remove the metal plate [2].

Disconnect the connector [1], and remove the duplex transport motor [2]. Remove the sub hopper assy. Disconnect six coonectors [1], and remove the harnesses from eight wire saddles [2]. Remove six screws [1], and separate the sub hopper assy [2].

Remove four screws [1], disconnect the connector [2], and remove the transport motor [3]. Remove four screws [1], disconnect the connector [2], and remove the color PC motor [3]. Remove four screws [1], disconnect the connector [2], and remove the fusing motor [3]. Remove two screws [2], and remove the switchback motor [3]. Disconnect the connector [1], and remove the harness from the wire saddle [2]. Remove four screws [3], and remove the fusing pressure roller retraction motor assy [4].

Remove two screws [1], and remove the fusing pressure roller retraction motor [2]. Remove the harness from the wire saddle [1]. Remove the harness from the edge cover [1].

Remove four screws [2], disconnect two connectors [3], and remove the duct assy [4]. Remove the main drive unit. Remove three screws [1], and remove the color dev. Remove two screws [1], and remove the color dev.

Remove the tray 1. Remove the tray 2. Remove the harnesses from the edge cover [1], and disconnect two connectors [2] on the printer control board. Remove the harnesses from two wire saddles [1].

Remove four screws [1], and remove the paper feed lift-up unit [2]. Remove three screws [1], disconnect the connector [2], and remove the paper feed tray 1 lift-up motor [3]. Remove the paper feed lift-up unit. Remove three screws [1], disconnect the connector [2], and remove the paper feed tray 2 lift-up motor [3].

Remove the screw [1], and remove the waste toner duct [2]. Remove the screw [1] of the transfer belt cleaner cooling fan motor assy. Remove the harnesses from the edge cover [2], and remove the transfer belt cleaner cooling fan motor assy [3].

Remove two screws [1], disconnect the connector [2], and remove the transfer belt cleaner cooling fan motor [3].

Remove two screws [1] and the E- ring [2], and remove the metal plate [3]. Remove the gear [1]. Disconnect the connector [2], and remove the harness from two wire saddles [3]. Remove the E-ring [4], and remove the paper feed tray 1 paper feed clutch [5].

NOTE When mounting the paper feed tray 1 paper feed clutch, set the convex part of the stopper into the concave part of the paper feed tray 1 paper feed clutch [5]. Disconnect the connector [1], and remove the harness from two wire saddles [2].

Remove the E-ring [3], and remove the paper feed tray 2 vertical trans- port clutch [4]. NOTE When mounting the paper feed tray 2 vertical transport clutch, set the convex part of the stopper into the concave part of the paper feed tray 2 vertical transport clutch [4]. Remove the E-ring [4], and remove the paper feed tray 2 paper feed clutch [5].

NOTE When mounting the paper feed tray 2 paper feed clutch, set the convex part of the stopper into the concave part of the paper feed tray 2 paper feed clutch [5]. Disconnect the connector [3], and remove the harness from the wire saddle [1] and the edge cover [2].

Remove the E-ring [4], and remove the manual paper feed clutch [5]. NOTE When mounting the manual paper feed clutch, set the convex part of the stopper into the concave part of the manual paper feed clutch [5]. Remove the conveyance unit. Disconnect the connector [1], remove the E-ring [2], and remove the registration roller clutch [3]. NOTE When mounting the registration roller clutch, set the convex part of the stopper into the concave part of the registration roller clutch [3].

Disconnect the connector [1], and remove the harnesses from the wire saddle [2] and the edge cover [3]. Remove the harnesses from four edge covers [1]. Remove three screws [2], and remove the metal plate [3]. Remove the shutter lever [1]. Remove the screw [1], the pin [2] and the spacer [3], and remove the IDC registration sensor shutter sole- noid [4]. Remove two screws [1]. Take the same procedure when replacing the pads for the other colors. Remove the PH unit. Unhook the tab [1], and remove the cleaning pad [2].

Remove the exposure unit. Remove the scanner motor. Remove the hook side spring [1] of the scanner drive cables. Remove the bead side [1] of the scanner drive cables from the adjust- ment anchor. Remove the screw [1], and remove the scanner drive gear [2]. Remove the bearing [3]. Remove the scanner drive cables [2] from each pulley [1]. Remove the screw [3] each, and remove two pulleys [1] from the shaft. Set the round bead [1] of the scan- ner drive cable silver into the hole of the pulley [2] as shown in the illus- tration.

NOTE Make sure that the bead securely rests in the hole of the pulley. Twist the scanner drive cable [3] of which side has the bead at the end around the pulley 4 times as shown in the illustration. Twist the hook side scanner drive cable [4] around the pulley 4 times as shown in the illustration.

NOTE Make sure that no part of the cable rides on the other. Set the round bead [1] of the scan- ner drive cable black into the hole of the pulley [2] as shown in the illus- tration. Apply the tape to fix the scanner drive cable to the pulley [1]. NOTE Set the pulley at the direction as shown in the illustration.

Fix the pulley at the position as shown in the illustration. Apply the screw lock on the screw. Install the shaft [1] and the bearing [2]. Install the gear [4] with the screw [3]. NOTE Apply the screw lock on the screw.

Run the bead side scanner drive cable [1] from the pulley B [2] to the pulley C [3]. Attach the bead to the adjustment anchor [4]. Run the hook side scanner drive cable [1] around the pulley D [2] and the pulley C [3] in this order. Run the scanner drive cable from the pulley C [1] to the hole [2] on the scanner left frame, and pass the cable through the hole [2].

Attach the spring [1] to the cable and attach the other end of the spring to the hook [2] on the scanner left frame. Install the scanner drive cable with the same procedure as the front one. Attach the spring [2] to the hooks [1] of the front and rear scanner drive cables. Adjust the positioning of the exposure unit and mirrors unit. Using a cleaning pad, wipe the trans- fer belt [1].

NOTE Do not wipe out with water. Do not wipe out with any solvents. Clean the PH window by putting the PH window cleaning jig back and forth a couple times. Using a cleaning pad dampened with alcohol, wipe the tray 1 feed roller [1] clean of dirt.

Using a cleaning pad dampened with alcohol, wipe the tray 1 pick-up roller [1] clean of dirt. Using a cleaning pad dampened with alcohol, wipe the tray 1 separation roller [1] clean of dirt. Using a cleaning pad dampened with alcohol, wipe the tray 2 feed roller [1] clean of dirt. Using a cleaning pad dampened with alcohol, wipe the tray 2 pick-up roller [1] clean of dirt.

Using a cleaning pad dampened with alcohol, wipe the tray 2 separation roller [1] clean of dirt. Using a cleaning pad dampened with alcohol, wipe the tray 2 transport roll- ers [1] clean of dirt. Using a cleaning pad dampened with alcohol, wipe the manual bypass tray feed roller [1] clean of dirt.

Using a cleaning pad dampened with alcohol, wipe the manual bypass tray separation roller [1] clean of dirt. Using a cleaning pad dampened with alcohol, wipe the original glass [1] clean of dirt. Open the ADF, and remove the slit glass cleaner [2]. Clean the slit glass [2] with the cleaner [1]. Using a cleaning pad dampened with alcohol, wipe the scanner rails [1] clean of dirt.

NOTE Apply lubricant after cleaning. Remove two screws [1] and lens cover [2]. Using a cleaning pad dampened with alcohol, wipe the lens [1] clean of dirt. Unhook two tabs [1], and remove the CCD sensor cover [2].

Using a cleaning pad dampened with alcohol, wipe the CCD sensor [1] clean of dirt. More than one firmware data with a single model or multiple models can be stored in the USB memory. Maximum of fifteen files When storing more than one firmware data, make a folder with a name model code FW A0EDFW for this machine right under the root directory. File names can be set arbitrarily When making a folder and storing more than one firmware data, it is also neces- sary to copy the firmware data A0EDFW.

Turn OFF the main power switch and the sub power switch. Remove the screw [1]. Lift up the cover [2] of the USB port. It cannot be updated when connected to another USB port. Turn ON the main power switch and the sub power switch. Select [YES]. When the BootRom file is in the firmware data, [RootRom] key is displayed. Press- ing the key updates data. When more than one firmware are stored in step 1, pressing [FW Data Select] enables selection.

Data of other models cannot be selected. At this time, the Start key starts blinking red. Check that the control panel shows the message indicating that the data has been rewritten correctly [Downloading Completed]. Check also the check sum value [Check Sum ] shown on the control panel. The Start key lights blue. NOTE When turning the main power switch ON for the first time after the firmware is updated, data may sometimes be internally updated.

In that case, the following message will be displayed. Never turn the main power switch OFF until either the serial number input screen or the trouble code screen is displayed. Call the Service Mode to the screen.

Select [Firmware Version]. Make sure if the version of firmware is updated. Perform the data rewriting procedure again. If the procedure is abnormally terminated, change the USB memory for a new one and try another rewriting sequence. If the procedure is still abnormally terminated, change the board that has caused NG and carry out data rewriting procedure.

The main body is connected to such a network environment that the firmware can be downloaded on the internet using the ftp or http protocol. The Internet ISW will not operate under the following conditions. Main power switch is set to OFF. Sub power switch is set to OFF. Machine is in idle with suspended job Paper jam has occurred Image file is in the memory Model or the circuit board of the program does not match 7.

Internet ISW Set 1. NOTE Settings such as server setting, etc. When the following setting is set to ON, ON cannot be selected on this setting.

Protocol setting It performs the setting concerning the protocol ftp or http for connecting to the Internet ISW. When connecting to the program server using a proxy server, perform the setting for a proxy server. Select [Port Number], and set the port number for the proxy server from 1 through When Authentication is necessary for accessing to the proxy server, select [Authentication], and select [ON].

Select [Log-in Name], and enter the login name on the on-screen keyboard. Select [Password], and enter the password on the on-screen keyboard. Select [Connection Time Out], and set the time for the connection time out from 1 through Since with PASV mode, the client with restriction sets the port number, data trans- mission port can be secured to enable the file transmission.

Forwarding access setting To make the access setting for the program server which stores the firmware data. Touch [Forwarding Access Setting]. Select [Password], and enter the password which is necessary for connecting to the program server on the on-screen keyboard, and touch [END]. Select [File Name], and enter the file name of the firmware data to be downloaded on the on-screen keyboard, and touch [END].

Touch [END] to finish setting. Conducting rewriting on the control panel. Touch [ISW Start]. The main body will automatically start running, and it starts accessing the server.

NOTE Unless one of the keys on the control panel is pressed, firmware is updated after 30 seconds when the unit has restarted. During firmware updating 1. The message to indicate the status will be displayed on the screen while connecting or transferring data. Completed or failed 1 Firmware updated normally 1. When the Firmware is normally updated, restart the main body in auto or manual mode to display the outcome, and touch [OK] to return to the main screen.

When updating failed to complete due to the trouble on connecting to the network, an error code and the message will be displayed. Restart the main body in auto or manual mode, and touch [OK]. It can be used with the firmware version before conducting updating.

Check the settings for the network by error codes, and try updating again. Once firmware updating has started, the ROM in the main body will be deleted. When it failed right after updating has started, restart the main body, and shift to the standby screen to retry downloading. When updating on the control panel, touch [settings] on the standby screen, and check the Network settings again. Confirming the firmware version 1. Select the [Firmware Version]. Check if the firmware version is updated.

Check the Users network environment. LAN cables connection Check the status of the following set- ting. Check the network environment of the User. Check to see if the FTP server oper- ates normally. Check to see if FTP server normally operates. Check the IP address, users name, etc. Check to see if FTP server operates normally.

Wait for about 30 minutes and try it again. ISW being executed by other method. Wait for the current job to be completed and try it again. Turn sub power switch ON and try it again. Wait for the current Internet ISW to be completed. Error code Description Countermeasure Control panel 7. It failed to lock the operation. It failed to lock the job because the operation is already locked with PSWC, etc. Check if the following setting is set to Valid.

The header of the file which has been read has an error. The size of the file to be downloaded is too large. During the process by the subset pro- gram, it has to be in the Failed status unless the Internet ISW is successfully conducted.

This code is used tempo- rarily to make it in error status. Procedure for directly mounting the key counter to the main unit is described below. For mounting the key counter to the optional working table WT, refer to WT- installation manual.

Remove the scanner right cover [1]. Cut out the knockouts [2] of the scanner right cover. Remove two caps [3].

Remove the harness for the key counter from three wire saddles [1]. Mount the scanner right cover [1], and insert the harness for the key counter through the hole [2] knock- outs were removed from. Using two screws [2], secure the counter mounting bracket [1]. NOTE Secure the counter mounting bracket passing the connector into the bracket. Use the two long screws V M4 x 18 in the key counter kit to secure the counter mounting bracket.

Mount the edge cover [1] to the counter mounting bracket and set the harness to the edge cover. Connect the key counter socket con- nector [2]. Using two screws [4], secure the counter socket [3].

Using two screws [2], secure the key counter cover [1]. Set color mode and message. Using the screw [1], mount the origi- nal size detection 2 sensor PS [2] and fix it. Select [Service Mode] [Machine] [Org. Size Detecting Sensor Adj]. Check to make sure that the [Org. Size Detecting Sensor Option : Set] is displayed on the original size detection sensor adjustment screen.

Advance checks Before attempting to solve the customer problem, the following advance checks must be made. Check to see if: The power supply voltage meets the specifications.

The power supply is properly grounded. The machine shares the power supply with any other machine that draws large current intermittently e. The installation site is environmentally appropriate: high temperature, high humidity, direct sunlight, ventilation, etc. The original has a problem that may cause a defective image.

The density is properly selected. If you get stuck in repairing a defective appliance download this repair information for help. See below. Good luck to the repair! Please do not offer the downloaded file for sell only use it for personal usage! Page Ozone Filter Life Detection Page Theory of Operation Ver. Page Developing Section Page Drive Theory of Operation Ver. Page Color dev. The Ds rollers are mounted coaxially with the developing roller and designed to be larger in diameter than the developing roller.

Page Developer Flow Page Auto Refining Developing System This provides development performance that responds to various types of environment of the users. Toner scattering prevention plate Toner scattering Page Developing Cooling Page Developing Unit Detection The board detects different states of the corresponding developing unit. Life counter TCR sensor Image Page Developing Unit Life Detection Page Toner Supply Section Page Toner Hopper Drive Page Toner Flow Toner conveying screw drive 1.

Drive of the toner supply motor is transmitted to the toner conveying screws of two colors of toner. A one-way clutch is mounted coaxially with the toner conveying screw. It prevents the machine from being operated with the toner cartridge yet to be mounted.

The protrusion functions to detect the mounting condition of the toner cartridge. It prevents the machine from being operated with the toner replenishing port of the toner cartridge closed. Page Toner Spillage Prevention Shutter Page Front Door Mechanism Page St Image Transfer Section The transfer belt is rotated counterclockwise.

The auto color mode is called the ACS auto color selection mode. Black printing after switched to Paper length Black printing in color mode black mode mm or under 2 sheets or less Page Transfer Belt Cleaning The toner collecting screw rotates in time with rotation of the transfer belt. Controlled item Counting unit Printed page count If the printed counter reaches the threshold, the machine determines that the image transfer belt unit has reached a new state.

There is a shutter mechanism provided for the sensor to prevent it from being contaminated. Reaching life display Life stop display reaching life threshold value life stop threshold value Page Theory of Operation Ver. Page Toner Collecting Section It prevents the machine from being operated with the waste toner box yet to be mounted in place. Detection made by the waste toner full sensor is used for detecting a new waste toner box.

Page Operation A torque limited is mounted on the shaft of the separator roller. These two roll- ers must be replaced with new ones at the same time. Page Paper Size Detection Control Page Remaining Paper Detection Control If the paper lift-up plate is located at the standby position lower position , however, the detection result is not incorporated under any of the following conditions because of the limited detection range of the manual paper detection sensor.

Page Paper Feed Section Page Tray2 Theory of Operation Ver. The machine then determines that the tray is slid into position. Upstream: Refers to the source side of paper supply relative to the paper feeding direc- tion Downstream: Refers to the destination side of paper transport relative to the paper feed- ing direction These three rollers must be replaced with new ones at the same time.

Page Right Door Mechanism When the registration roller clutch is energized, the driving force of the transport motor is transmitted to the reg- istration roller. A loop is formed at the leading edge of the paper because the paper feed roller continues rotating. The loop corrects skew in the paper. Page Fusing Drive Release Mechanism The loop corrects variations between the paper conveyance speed during the image transfer and the fusing speed.

Page Fusing Temperature Control In the control, the set temperature for the fusing belt and fusing pressure roller is controlled to an optimum value according to the environment.

Page Protection From Abnormal Temperatures Page Duplex Print Control Page Image Stabilization Control Page Operation Sequence

Konica minolta bizhub c360 service manual free download

Page 76 Theory of Operation Ver. Page Color Skew Correction Control 9. This may cause color skew problems. To prevent the problems, individual G3 lenses that correspond to Y, M, and C respectively have a color skew auto adjustment mechanism. Page 78 Theory of Operation Ver. This could result in image problems, including white bands or white lines on the print image. Page Image Processing 9.

See P. Page Drive Page 85 The potential left on the photo conductor after the toner image is transferred is neutral- ized by turning ON the erase lamp and any potential left on the surface of the photo con- ductor is neutralized. Page Photo Conductor Cleaning Part of the toner image that is not transferred is left on the surface of the photo conduc- tor.

Page 90 Theory of Operation Ver. Page Charge Corona Control Charge discharged from the comb electrode causes the surface of the photo conductor to become uniformly charged via the charge corona control plate. Page Ozone Filter Page 95 Page 97 If the drum rotation time counter value reaches the thresh- old, the machine determines that the drum unit has reached a new state. Page 98 Theory of Operation Ver.

Page 99 Page Ozone Filter Life Detection Page Theory of Operation Ver. Page Developing Section Page Drive Theory of Operation Ver. Page Color dev. The Ds rollers are mounted coaxially with the developing roller and designed to be larger in diameter than the developing roller. Page Developer Flow Page Auto Refining Developing System This provides development performance that responds to various types of environment of the users.

Toner scattering prevention plate Toner scattering Page Developing Cooling Page Developing Unit Detection The board detects different states of the corresponding developing unit. Life counter TCR sensor Image Page Developing Unit Life Detection Page Toner Supply Section Page Toner Hopper Drive Page Toner Flow Toner conveying screw drive 1. Drive of the toner supply motor is transmitted to the toner conveying screws of two colors of toner.

A one-way clutch is mounted coaxially with the toner conveying screw. It prevents the machine from being operated with the toner cartridge yet to be mounted. The protrusion functions to detect the mounting condition of the toner cartridge. It prevents the machine from being operated with the toner replenishing port of the toner cartridge closed.

Page Toner Spillage Prevention Shutter Page Front Door Mechanism Page St Image Transfer Section The transfer belt is rotated counterclockwise. The auto color mode is called the ACS auto color selection mode. Black printing after switched to Paper length Black printing in color mode black mode mm or under 2 sheets or less Page Transfer Belt Cleaning The toner collecting screw rotates in time with rotation of the transfer belt. Controlled item Counting unit Printed page count If the printed counter reaches the threshold, the machine determines that the image transfer belt unit has reached a new state.

Page Toner Collecting Section It prevents the machine from being operated with the waste toner box yet to be mounted in place. Detection made by the waste toner full sensor is used for detecting a new waste toner box. Page Operation A torque limited is mounted on the shaft of the separator roller.

These two roll- ers must be replaced with new ones at the same time. Page Paper Size Detection Control Page Remaining Paper Detection Control If the paper lift-up plate is located at the standby position lower position , however, the detection result is not incorporated under any of the following conditions because of the limited detection range of the manual paper detection sensor. Page Paper Feed Section Page Tray2 Theory of Operation Ver.

The machine then determines that the tray is slid into position. Upstream: Refers to the source side of paper supply relative to the paper feeding direc- tion Downstream: Refers to the destination side of paper transport relative to the paper feed- ing direction These three rollers must be replaced with new ones at the same time. Page Right Door Mechanism When the registration roller clutch is energized, the driving force of the transport motor is transmitted to the reg- istration roller.

A loop is formed at the leading edge of the paper because the paper feed roller continues rotating. The loop corrects skew in the paper.

Page Fusing Drive Release Mechanism The loop corrects variations between the paper conveyance speed during the image transfer and the fusing speed. Page Fusing Temperature Control In the control, the set temperature for the fusing belt and fusing pressure roller is controlled to an optimum value according to the environment.

Page Protection From Abnormal Temperatures Page Duplex Print Control Download the latest version of the konica minolta bizhub c series pcl driver for your computer's operating system.

Top 4 download periodically updates drivers information of konica minolta pcl printer driver full drivers versions from the publishers, but some download links are directly from our mirrors or publisher's website, konica. Bizhub all in one printer pdf manual download. Click here to download for more information, please contact konica minolta customer service or service provider. Top 4 download periodically updates drivers information of konica minolta pcl printer driver full drivers versions from the publishers, but some download links are directly from our mirrors or publisher's website, konica minolta pcl printer driver torrent files or shared files from free file.

Printer fonts 80 pcl latin; Konica minolta seriesxps driver direct download was reported as adequate by a large percentage of our reporters, so it should usb devices. View and download konica minolta bizhub quick start manual online. Here, we are providing konica minolta bizhub driver download link for windows xp, vista, 7, 8, 8. The following issue is solved in this driver: The drivers provided on this page are for konica minolta seriespcl, and most of them are for windows operating system.

Print functions direct print of pcl; Download the latest drivers, manuals and software for your konica minolta device. The drivers provided on this page are for konica minolta seriespcl, and most of them are for windows operating system. The following issue is solved in this driver: postscript 3 emulation latin.

This symbol indicates transition of the control panel to access a desired menu item. This symbol indicates a desired page. Page Key Symbols Original and paper indications w indicates the paper size with the length X being longer than the width Y.

Page Information Also, these restrictions differ depending on the device that make up the network. For details, contact your network administrator. If PageScope Authentication Manager is used for authentication, ask your server administrator about the login procedure. Page Mfp Authentication Enter the user name, password and server name, and then press either [Login] or the Access key on the con- trol panel. Account Track Enter the account name and password, and then press either [Login] or the Access key on the control panel.

Page Restriction On File Name The characters do not appear beside "File Name", but is added automatically as part of the name when the file is transmitted.

Page Overview Scanned data can be sent to the specified E-mail address. Select destinations from the touch panel of this machine, and send scanned data as an E-mail attachment. Original 2. Main unit 3.

Memory 4. SMTP server 6. POP server 7. Page Ftp Transmission Scanned data can be sent to a shared folder on a specified computer. Enter the intended host name, file path and other information from the touch panel of this machine. Scanned data 5. Page User Box Filing The data uploaded to the server can be downloaded from a computer on the network. Server 6. Page Web Service G3 fax can be sent or received.

Destinations can be selected from the touch panel of this machine for broad- cast transmission. Also, some of the edit functions that are available for Scan can be added when sending a fax.

Send 2. Page Polling Polling TX. Receive 2. Send 3. Bulletin board 4. View 5. Register 6. SMTP server 5. POP server 6. Receive E-mail 7. Fax can be sent or received in color. Only the differences from G3 fax 1. Intranet 2. Page 31 [User's Guide Box Opera- tions].

Page 32 Do not apply extreme pressure to the touch panel, otherwise the touch panel may be scratched or dam- aged. Never push down on the touch panel with force, and never use a hard or pointed object to make a selection in the touch panel. Page Touch Panel Appears when there is a message indicating that consumables must be re- placed or the machine requires maintenance. Press this icon to display the message, and then perform the replacement or maintenance procedure.

If the Fax Kit FK is not installed Fax destinations or functions related to fax operation are not displayed. Page Job List [Delete]. Check the message that appears, and delete the job. There are the following four types of jobs. To delete a job, press [De- lete].

Press one of these buttons. The job list of the selected line appears. Page 40 To delete a job, press [Delete]. Page 41 Press this button to delete the selected job. To delete a job, press [Delete]. Page 42 When [Job History Thumbnail Display] is set to [ON] in the setting menu, if a history is selected from the list, the image in the first page is displayed in the area on the left. Check Job - Check Job Settings - Scan Settings You can check the details of scan settings basic setting, scan setting and application setting.

Press either Back] or [Forward ] to check. Press either [ Back] or [Forward ] to check. Connection to network Connect a UTP cable category 5 or later recommended connected to the network to the Ethernet connector on the machine. Page Network Settings Connect one end of the modular cable to the telephone adapter, and the other end to the predetermined con- nector of this machine. For details on the connector location, refer to the [User's Guide Copy Operations].

Page Store Address Web service destinations cannot be registered with an address book. Enter directly the Web service destination instead. This is convenient for sending data to multiple destinations simultaneously. Page Optional Settings Reference For details, refer to page Reference For details, refer to page Page Using The Web Service 4. When the confirmation dialog box appear, click [Close]. Select [Web Service] on the control panel of this machine, to ensure that the connection to the compu- ter is established.

Page Operation Flow Address Book p. Page 54 [Begin Authentication] to start sending. Specify the destination Address Book p. Press Mode Memory. Page 57 Operation flow Select a program, and press [OK]. Configure Scan Settings p. Load the original To check the advanced preview, press Proof Copy. Page Broadcasting The following describes the procedure for sending a fax to multiple destinations simultaneously. Specify multiple destinations. Address Book p. Page 59 [Begin Authentication] to start sending.

Page Using The Advanced Preview 4 times and 8 times of the full size display in this or- der. In the enlarged display mode, use the scroll bars located in the right and the bottom of the im- age to view to the desired portion of the document. Page 61 Change some of the settings you have configured prior to scanning the original. For details, refer to page Reference Select a page directly to rotate the image of the selected page by degrees.

Preview - View Status Determine whether to scan subsequent pages or not. Item Description [Finish] To scan subsequent pages of the originals current- ly shown, make sure [Finish] is not selected.

Page Sending With The Advanced Preview Settings, the screen for specifying the direction in which the original is loaded does not ap- pear. For details on [Original Direction Confirmation Screen], refer to page Press the Start key. The original is scanned, and the Preview screen appears.

Page 64 Check the preview image, and rotate the image or change settings as needed. Transmission begins. Page [Off-Hook] [Sharpness] p. Page [Original Settings] [Mixed Original] p. The display position for each tab varies depending on the User Settings. Page Home Scan To Home Address Type This function enables you to search by the destination type configured when registered destination.

For details on address book registration, refer to page Page Index Index Displays the destinations based on the index that was specified when the destination was registered. Page Detail Search [Address], and enter an index. Search Option In the Detail Search screen, select a condition to display search options. Select the option you want to add to the search conditions, then press [OK]. Page 75 Address Book Reference To configure whether to display the search option screen and options displayed on that screen, use [Search Option Settings] in the setting menu.

Enter the fax number, and then press [Send]. Reference For details on the Confirm Address function, refer to page Page User Box Select the compression type receivable on the receiver side.

Page Ip Address Fax Use the keypad to enter the sending port number using a value from 1 to Page Pc Smb You can check the folder configuration on the destination computer. You can directly specify the destination folder if necessary. Page [Password] [Port Number] Enter the port number. Page Web Service Data can be scanned and saved by sending command to this machine from the computer.

For the detailed procedure, refer to page Page Job History [Name] When you use the address book for sending, [Name] is displayed in the job history. If you press [Name], [Dest] in the job history changes to [Name], and the registered name appears. Page Address Search Enter the E-mail address in the touch panel.

allinone 02spercelnazogz

Saturday, April 29, 2023

Konica minolta bizhub c360 service manual free download

Looking for:

Konica minolta bizhub c360 service manual free download.Download Center

Konica minolta bizhub c360 service manual free download

Konica minolta bizhub c360 service manual free download

No comments:

Post a Comment

Konica minolta bizhub c360 service manual free download

Report Abuse